A vulnerability in the Border Gateway Protocol (BGP) over an Ethernet Virtual Private Network (EVPN) for Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause the device to reload, resulting in a denial of service (DoS) condition, or potentially corrupt the BGP routing table, which could result in network instability. The vulnerability exists due to changes in the implementation of the BGP MPLS-Based Ethernet VPN RFC (RFC 7432) draft between IOS XE software releases. When the BGP Inclusive Multicast Ethernet Tag Route or BGP EVPN MAC/IP Advertisement Route update packet is received, it could be possible that the IP address length field is miscalculated. An attacker could exploit this vulnerability by sending a crafted BGP packet to an affected device after the BGP session was established. An exploit could allow the attacker to cause the affected device to reload or corrupt the BGP routing table; either outcome would result in a DoS. The vulnerability may be triggered when the router receives a crafted BGP message from a peer on an existing BGP session. This vulnerability affects all releases of Cisco IOS XE Software prior to software release 16.3 that support BGP EVPN configurations. If the device is not configured for EVPN, it is not vulnerable. Cisco Bug IDs: CSCui67191, CSCvg52875.
A vulnerability in the CLI of Cisco NX-OS System Software could allow an authenticated, local attacker to perform a command injection attack. An attacker would need valid administrator credentials to perform this exploit. The vulnerability is due to insufficient input validation of command arguments. An attacker could exploit this vulnerability by injecting crafted command arguments into a vulnerable CLI command. An exploit could allow the attacker to execute arbitrary commands as root. This vulnerability affects the following products running Cisco NX-OS System Software: Multilayer Director Switches, Nexus 2000 Series Fabric Extenders, Nexus 3000 Series Switches, Nexus 3500 Platform Switches, Nexus 5000 Series Switches, Nexus 5500 Platform Switches, Nexus 5600 Platform Switches, Nexus 6000 Series Switches, Nexus 7000 Series Switches, Nexus 7700 Series Switches, Nexus 9000 Series Switches in standalone NX-OS mode, Nexus 9500 R-Series Line Cards and Fabric Modules, Unified Computing System Manager. Cisco Bug IDs: CSCvf15113, CSCvf15122, CSCvf15125, CSCvf15131, CSCvf15143, CSCvg04088.
A vulnerability in the TCL scripting subsystem of Cisco NX-OS System Software could allow an authenticated, local attacker to escape the interactive TCL shell and gain unauthorized access to the underlying operating system of the device. The vulnerability exists due to insufficient input validation of user-supplied files passed to the interactive TCL shell of the affected device. An attacker could exploit this vulnerability to escape the scripting sandbox and execute arbitrary commands on the underlying operating system with the privileges of the authenticated user. To exploit this vulnerability, an attacker must have local access and be authenticated to the targeted device with administrative or tclsh execution privileges. This vulnerability affects the following products running Cisco NX-OS System Software: Multilayer Director Switches, Nexus 2000 Series Fabric Extenders, Nexus 3000 Series Switches, Nexus 3500 Platform Switches, Nexus 5000 Series Switches, Nexus 5500 Platform Switches, Nexus 5600 Platform Switches, Nexus 6000 Series Switches, Nexus 7000 Series Switches, Nexus 7700 Series Switches, Nexus 9000 Series Switches in standalone NX-OS mode, Nexus 9500 R-Series Line Cards and Fabric Modules, Unified Computing System Manager. Cisco Bug IDs: CSCve93750, CSCve93762, CSCve93763, CSCvg04127.
A vulnerability in the CLI of Cisco NX-OS System Software could allow an authenticated, local attacker to read the contents of arbitrary files. The vulnerability is due to insufficient input validation for a specific CLI command. An attacker could exploit this vulnerability by issuing a crafted command on the CLI. An exploit could allow the attacker unauthorized access to read arbitrary files on the underlying local file system. On products that support multiple virtual device contexts (VDCs), this vulnerability could allow an attacker to read files from any VDC. This vulnerability affects the following products running Cisco NX-OS System Software: Multilayer Director Switches, Nexus 2000 Series Fabric Extenders, Nexus 3000 Series Switches, Nexus 5000 Series Switches, Nexus 5500 Platform Switches, Nexus 5600 Platform Switches, Nexus 6000 Series Switches, Nexus 7000 Series Switches, Nexus 7700 Series Switches, Nexus 9000 Series Fabric Switches in Application Centric Infrastructure (ACI) mode, Nexus 9000 Series Switches in standalone NX-OS mode, Nexus 9500 R-Series Line Cards and Fabric Modules, Unified Computing System Manager. Cisco Bug IDs: CSCve51707, CSCve93961, CSCve93964, CSCve93965, CSCve93968, CSCve93974, CSCve93976.
A vulnerability in the Local Packet Transport Services (LPTS) ingress frame-processing functionality of Cisco IOS XR Software could allow an unauthenticated, remote attacker to cause one of the LPTS processes on an affected system to restart unexpectedly, resulting in a brief denial of service (DoS) condition. The vulnerability is due to incomplete LPTS frame validation by the affected software. An attacker could exploit this vulnerability by sending crafted XML requests to the management interface of an affected system. A successful exploit could allow the attacker to cause one of the LPTS processes on the affected system to restart unexpectedly, which would impact LPTS traffic and cause a brief DoS condition while the process restarts. Cisco Bug IDs: CSCvf76332.
A "Cisco WebEx Network Recording Player Denial of Service Vulnerability" exists in Cisco WebEx Network Recording Player for Advanced Recording Format (ARF) and WebEx Recording Format (WRF) files. A remote attacker could exploit this by providing a user with a malicious ARF or WRF file via email or URL and convincing the user to launch the file. Exploitation of this could cause an affected player to crash and, in some cases, could allow arbitrary code execution on the system of a targeted user. Cisco Bug IDs: CSCve11545, CSCve02843, CSCve11548.
A vulnerability in Cisco WebEx Meeting Center could allow an authenticated, remote attacker to initiate connections to arbitrary hosts, aka a "URL Redirection Vulnerability." The vulnerability is due to insufficient access control for HTTP traffic directed to the Cisco WebEx Meeting Center. An attacker could exploit this vulnerability by sending a malicious URL to the Cisco WebEx Meeting Center. An exploit could allow the attacker to connect to arbitrary hosts. Cisco Bug IDs: CSCvf63843.
A vulnerability in Session Initiation Protocol (SIP) call handling in Cisco IP Phone 8800 Series devices could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition because the SIP process unexpectedly restarts. All active phone calls are dropped as the SIP process restarts. The vulnerability is due to incomplete input validation of the SIP packet header. An attacker could exploit this vulnerability by sending a malformed SIP packet to a targeted phone. An exploit could allow the attacker to cause a DoS condition because all phone calls are dropped when the SIP process unexpectedly restarts. Cisco Bug IDs: CSCvc62590.
A vulnerability exists in the process of creating default IP blocks during device initialization for Cisco ASA Next-Generation Firewall Services that could allow an unauthenticated, remote attacker to send traffic to the local IP address of the device, bypassing any filters that are configured to deny local IP management traffic. The vulnerability is due to an implementation error that exists in the process of creating default IP blocks when the device is initialized, and the way in which those IP blocks interact with user-configured filters for local IP management traffic (for example, SSH to the device). An attacker could exploit this vulnerability by sending traffic to the local IP address of the targeted device. A successful exploit could allow the attacker to connect to the local IP address of the device even when there are filters configured to deny the traffic. Cisco Bug IDs: CSCvd97962.
A vulnerability in the SNORT detection engine of Cisco Firepower System Software could allow an unauthenticated, remote attacker to bypass a file policy that is configured to block the Server Message Block Version 2 (SMB2) protocol. The vulnerability is due to the incorrect detection of an SMB2 file when the detection is based on the length of the file. An attacker could exploit this vulnerability by sending a crafted SMB2 transfer request through the targeted device. A successful exploit could allow the attacker to bypass filters that are configured to block SMB2 traffic. Cisco Bug IDs: CSCve58398.
A vulnerability in the H.264 decoder function of Cisco Meeting Server could allow an unauthenticated, remote attacker to cause a Cisco Meeting Server media process to restart unexpectedly when it receives an illegal H.264 frame. The vulnerability is triggered by an H.264 frame that has an invalid picture parameter set (PPS) value. An attacker could exploit this vulnerability by sending a malformed H.264 frame to the targeted device. An exploit could allow the attacker to cause a denial of service (DoS) condition because the media process could restart. The media session should be re-established within a few seconds, during which there could be a brief interruption in service. Cisco Bug IDs: CSCvg12559.
A vulnerability in the web interface of Cisco Jabber could allow an authenticated, local attacker to retrieve user profile information from the affected software, which could lead to the disclosure of confidential information. The vulnerability is due to a lack of input and validation checks in the affected software. An attacker could exploit this vulnerability by authenticating locally to an affected system and then issuing specific commands to the affected software. A successful exploit could allow the attacker to view all profile information for a user instead of only certain Jabber parameters that should be visible. This vulnerability affects all releases of Cisco Jabber prior to Release 1.9.31. Cisco Bug IDs: CSCve52418.
A vulnerability in the cluster database (CDB) management component of Cisco Expressway Series Software and Cisco TelePresence Video Communication Server (VCS) Software could allow an authenticated, remote attacker to cause the CDB process on an affected system to restart unexpectedly, resulting in a temporary denial of service (DoS) condition. The vulnerability is due to incomplete input validation of URL requests by the REST API of the affected software. An attacker could exploit this vulnerability by sending a crafted URL to the REST API of the affected software on an affected system. A successful exploit could allow the attacker to cause the CDB process on the affected system to restart unexpectedly, resulting in a temporary DoS condition. Cisco Bug IDs: CSCve77571.
A vulnerability in the detection engine parsing of IPv6 packets for Cisco Firepower System Software could allow an unauthenticated, remote attacker to cause high CPU utilization or to cause a denial of service (DoS) condition because the Snort process restarts unexpectedly. The vulnerability is due to improper input validation of the fields in the IPv6 extension header packet. An attacker could exploit this vulnerability by sending a malicious IPv6 packet to the detection engine on the targeted device. An exploit could allow the attacker to cause a DoS condition if the Snort process restarts and traffic inspection is bypassed or traffic is dropped. This vulnerability is specific to IPv6 traffic only. This vulnerability affects Cisco Firepower System Software Releases 6.0 and later when the software has one or more file action policies configured and is running on any of the following Cisco products: 3000 Series Industrial Security Appliances (ISR), Adaptive Security Appliance (ASA) 5500-X Series with FirePOWER Services, Adaptive Security Appliance (ASA) 5500-X Series Next-Generation Firewalls, Advanced Malware Protection (AMP) for Networks, 7000 Series Appliances, Advanced Malware Protection (AMP) for Networks, 8000 Series Appliances, FirePOWER 7000 Series Appliances, FirePOWER 8000 Series Appliances, Firepower Threat Defense for Integrated Services Routers (ISRs), Firepower 2100 Series Security Appliances, Firepower 4100 Series Security Appliances, Firepower 9300 Series Security Appliances, Virtual Next-Generation Intrusion Prevention System (NGIPSv) for VMware. Cisco Bug IDs: CSCvd34776.
A vulnerability in the implementation of the direct authentication feature in Cisco Adaptive Security Appliance (ASA) Software could allow an unauthenticated, remote attacker to cause an affected device to unexpectedly reload, resulting in a denial of service (DoS) condition. The vulnerability is due to incomplete input validation of the HTTP header. An attacker could exploit this vulnerability by sending a crafted HTTP request to the local IP address of an affected device. A successful exploit could allow the attacker to cause the affected device to reload. This vulnerability affects Cisco Adaptive Security Appliance (ASA) Software that is running on the following Cisco products: ASA 5500 Series Adaptive Security Appliances, ASA 5500-X Series Next-Generation Firewalls, ASA Services Module for Cisco Catalyst 6500 Series Switches and Cisco 7600 Series Routers, ASA 1000V Cloud Firewall, Adaptive Security Virtual Appliance (ASAv), Firepower 4110 Security Appliance, Firepower 9300 ASA Security Module, ISA 3000 Industrial Security Appliance. Cisco Bug IDs: CSCvd59063.
A vulnerability in the Web Admin Interface of Cisco Meeting Server could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition. The vulnerability is due to insufficient bound checks performed by the affected software. An attacker could exploit this vulnerability by sending a malicious HTTP packet to the affected system. A successful exploit could allow the attacker to cause a reload of the Web Admin Server. Cisco Bug IDs: CSCve89149.
A vulnerability in the wireless controller manager of Cisco IOS XE could allow an unauthenticated, adjacent attacker to cause a restart of the switch and result in a denial of service (DoS) condition. The vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by submitting a crafted association request. An exploit could allow the attacker to cause the switch to restart. This vulnerability affects Cisco Catalyst 3650 and 3850 switches running IOS XE Software versions 16.1 through 16.3.3, and acting as wireless LAN controllers (WLC). Cisco Bug IDs: CSCvd45069.
A vulnerability in the web-based Wireless Controller GUI of Cisco IOS XE Software for Cisco 5760 Wireless LAN Controllers, Cisco Catalyst 4500E Supervisor Engine 8-E (Wireless) Switches, and Cisco New Generation Wireless Controllers (NGWC) 3850 could allow an authenticated, remote attacker to elevate their privileges on an affected device. The vulnerability is due to incomplete input validation of HTTP requests by the affected GUI, if the GUI connection state or protocol changes. An attacker could exploit this vulnerability by authenticating to the Wireless Controller GUI as a Lobby Administrator user of an affected device and subsequently changing the state or protocol for their connection to the GUI. A successful exploit could allow the attacker to elevate their privilege level to administrator and gain full control of the affected device. This vulnerability affects the following Cisco products if they are running Cisco IOS XE Software Release 3.7.0E, 3.7.1E, 3.7.2E, 3.7.3E, 3.7.4E, or 3.7.5E: Cisco 5760 Wireless LAN Controllers, Cisco Catalyst 4500E Supervisor Engine 8-E (Wireless) Switches, Cisco New Generation Wireless Controllers (NGWC) 3850. Cisco Bug IDs: CSCvd73746.
Multiple vulnerabilities in the implementation of the Common Industrial Protocol (CIP) feature in Cisco IOS 12.4 through 15.6 could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerabilities are due to the improper parsing of crafted CIP packets destined to an affected device. An attacker could exploit these vulnerabilities by sending crafted CIP packets to be processed by an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Cisco Bug IDs: CSCuz95334.
Multiple vulnerabilities in the implementation of the Common Industrial Protocol (CIP) feature in Cisco IOS 12.4 through 15.6 could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerabilities are due to the improper parsing of crafted CIP packets destined to an affected device. An attacker could exploit these vulnerabilities by sending crafted CIP packets to be processed by an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Cisco Bug IDs: CSCvc43709.
A vulnerability in the implementation of the PROFINET Discovery and Configuration Protocol (PN-DCP) for Cisco IOS 12.2 through 15.6 could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerability is due to the improper parsing of ingress PN-DCP Identify Request packets destined to an affected device. An attacker could exploit this vulnerability by sending a crafted PN-DCP Identify Request packet to an affected device and then continuing to send normal PN-DCP Identify Request packets to the device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. This vulnerability affects Cisco devices that are configured to process PROFINET messages. Beginning with Cisco IOS Software Release 12.2(52)SE, PROFINET is enabled by default on all the base switch module and expansion-unit Ethernet ports. Cisco Bug IDs: CSCuz47179.
A vulnerability in the Operations, Administration, Maintenance, and Provisioning (OAMP) credential reset functionality for Cisco Unified Customer Voice Portal (CVP) could allow an authenticated, remote attacker to gain elevated privileges. The vulnerability is due to a lack of proper input validation. An attacker could exploit this vulnerability by authenticating to the OAMP and sending a crafted HTTP request. A successful exploit could allow the attacker to gain administrator privileges. The attacker must successfully authenticate to the system to exploit this vulnerability. This vulnerability affects Cisco Unified Customer Voice Portal (CVP) running software release 10.5, 11.0, or 11.5. Cisco Bug IDs: CSCve92752.
A vulnerability in the email message filtering feature of Cisco AsyncOS Software for the Cisco Email Security Appliance could allow an unauthenticated, remote attacker to cause an affected device to run out of memory and stop scanning and forwarding email messages. When system memory is depleted, it can cause the filtering process to crash, resulting in a denial of service (DoS) condition on the device. This vulnerability affects software version 9.0 through the first fixed release of Cisco AsyncOS Software for Cisco Email Security Appliances, both virtual and hardware appliances, if the software is configured to apply a message filter or content filter to incoming email attachments. The vulnerability is not limited to any specific rules or actions for a message filter or content filter. Cisco Bug IDs: CSCvd29354.
A vulnerability in the HTTP web interface for Cisco Wide Area Application Services (WAAS) could allow an unauthenticated, remote attacker to cause an HTTP Application Optimization (AO) related process to restart, causing a partial denial of service (DoS) condition. The vulnerability is due to lack of input validation of user-supplied input parameters within an HTTP request. An attacker could exploit this vulnerability by sending a crafted HTTP request through the targeted device. An exploit could allow the attacker to cause a DoS condition due to a process unexpectedly restarting. The WAAS could drop traffic during the brief time the process is restarting. Cisco Bug IDs: CSCvc63048.
A vulnerability in the batch provisioning feature in Cisco Prime Collaboration Provisioning Tool could allow an authenticated, remote attacker to overwrite system files as root. The vulnerability is due to lack of input validation of the parameters in BatchFileName and Directory. An attacker could exploit this vulnerability by manipulating the parameters of the batch action file function. Cisco Bug IDs: CSCvd61766.
A vulnerability in the malware detection functionality within Advanced Malware Protection (AMP) of Cisco AsyncOS Software for Cisco Email Security Appliances (ESAs) could allow an unauthenticated, remote attacker to cause an email attachment containing malware to be delivered to the end user. The vulnerability is due to the failure of AMP to scan certain EML attachments that could contain malware. An attacker could exploit this vulnerability by sending an email with a crafted EML attachment through the targeted device. A successful exploit could allow the attacker to bypass the configured ESA email message and content filtering and allow the malware to be delivered to the end user. Vulnerable Products: This vulnerability affects Cisco AsyncOS Software for Cisco ESA, both virtual and hardware appliances, that are configured with message or content filters to scan incoming email attachments on the ESA. Cisco Bug IDs: CSCuz81533.
A vulnerability in the CLI of Cisco ASR 5000 Series Aggregated Services Routers running the Cisco StarOS operating system could allow an authenticated, local attacker to bypass the CLI restrictions and execute commands on the underlying operating system. The vulnerability is due to insufficient input sanitization of user-supplied input at the CLI. An attacker could exploit this vulnerability by crafting a script on the device that will allow them to bypass built-in restrictions. An exploit could allow the unauthorized user to launch the CLI directly from a command shell. Cisco Bug IDs: CSCvd47722. Known Affected Releases: 21.0.v0.65839.
A vulnerability in configuration modification permissions validation for Cisco Unified Communications Manager could allow an authenticated, remote attacker to perform a horizontal privilege escalation where one user can modify another user's configuration. The vulnerability is due to lack of proper Role Based Access Control (RBAC) when certain user configuration changes are requested. An attacker could exploit this vulnerability by sending an authenticated, crafted HTTP request to the targeted application. An exploit could allow the attacker to impact the integrity of the application where one user can modify the configuration of another user's information. Cisco Bug IDs: CSCve27331. Known Affected Releases: 10.5(2.10000.5), 11.0(1.10000.10), 11.5(1.10000.6).
A vulnerability in the UpgradeManager of the Cisco Prime Collaboration Provisioning Tool 12.1 could allow an authenticated, remote attacker to write arbitrary files as root on the system. The vulnerability is due to insufficient input validation. An attacker could exploit this vulnerability by triggering the upgrade package installation functionality. Cisco Bug IDs: CSCvc90304.
A vulnerability in the implementation of the H.264 protocol in Cisco Meeting Server (CMS) 2.1.4 could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected system. The vulnerability exists because the affected application does not properly validate Fragmentation Unit (FU-A) protocol packets. An attacker could exploit this vulnerability by sending a crafted H.264 FU-A packet through the affected application. A successful exploit could allow the attacker to cause a DoS condition on the affected system due to an unexpected restart of the CMS media process on the system. Although the CMS platform continues to operate and only the single, affected CMS media process is restarted, a brief interruption of media traffic for certain users could occur. Cisco Bug IDs: CSCve10131.
Cisco IOS 12.0 through 15.6, Adaptive Security Appliance (ASA) Software 7.0.1 through 9.7.1.2, NX-OS 4.0 through 12.0, and IOS XE 3.6 through 3.18 are affected by a vulnerability involving the Open Shortest Path First (OSPF) Routing Protocol Link State Advertisement (LSA) database. This vulnerability could allow an unauthenticated, remote attacker to take full control of the OSPF Autonomous System (AS) domain routing table, allowing the attacker to intercept or black-hole traffic. The attacker could exploit this vulnerability by injecting crafted OSPF packets. Successful exploitation could cause the targeted router to flush its routing table and propagate the crafted OSPF LSA type 1 update throughout the OSPF AS domain. To exploit this vulnerability, an attacker must accurately determine certain parameters within the LSA database on the target router. This vulnerability can only be triggered by sending crafted unicast or multicast OSPF LSA type 1 packets. No other LSA type packets can trigger this vulnerability. OSPFv3 is not affected by this vulnerability. Fabric Shortest Path First (FSPF) protocol is not affected by this vulnerability. Cisco Bug IDs: CSCva74756, CSCve47393, CSCve47401.
A vulnerability in the web interface of the Cisco Web Security Appliance (WSA) could allow an authenticated, remote attacker to perform command injection and elevate privileges to root. The attacker must authenticate with valid administrator credentials. Affected Products: Cisco AsyncOS Software 10.0 and later for WSA on both virtual and hardware appliances. More Information: CSCvd88862. Known Affected Releases: 10.1.0-204. Known Fixed Releases: 10.5.1-270 10.1.1-235.
A vulnerability in the web proxy functionality of the Cisco Web Security Appliance (WSA) could allow an unauthenticated, remote attacker to forward traffic from the web proxy interface of an affected device to the administrative management interface of an affected device, aka an Access Control Bypass Vulnerability. Affected Products: virtual and hardware versions of Cisco Web Security Appliance (WSA). More Information: CSCvd88863. Known Affected Releases: 10.1.0-204 9.0.0-485.
A vulnerability in the Server Message Block (SMB) protocol of Cisco Wide Area Application Services (WAAS) could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device due to a process restarting unexpectedly and creating Core Dump files. More Information: CSCvc63035. Known Affected Releases: 6.2(3a). Known Fixed Releases: 6.3(0.167) 6.2(3c)5 6.2(3.22).
A vulnerability in the backup and restore functionality of Cisco FireSIGHT System Software could allow an authenticated, local attacker to execute arbitrary code on a targeted system. More Information: CSCvc91092. Known Affected Releases: 6.2.0 6.2.1.
A vulnerability in the CLI of Cisco IOS XR Software could allow an authenticated, local attacker to elevate privileges to the root level. More Information: CSCvb99384. Known Affected Releases: 6.2.1.BASE. Known Fixed Releases: 6.2.11.3i.ROUT 6.2.1.29i.ROUT 6.2.1.26i.ROUT.
A vulnerability in the CLI of Cisco IOS XR Software could allow an authenticated, local attacker to execute arbitrary commands on the host operating system with root privileges, aka Command Injection. More Information: CSCvb99406. Known Affected Releases: 6.2.1.BASE. Known Fixed Releases: 6.2.1.28i.BASE 6.2.1.22i.BASE 6.1.32.8i.BASE 6.1.31.3i.BASE 6.1.3.10i.BASE.
A vulnerability in the ingress processing of fragmented TCP packets by Cisco Wide Area Application Services (WAAS) could allow an unauthenticated, remote attacker to cause the WAASNET process to restart unexpectedly, causing a denial of service (DoS) condition. More Information: CSCvc57428. Known Affected Releases: 6.3(1). Known Fixed Releases: 6.3(0.143) 6.2(3c)6 6.2(3.22).
A vulnerability in Session Initiation Protocol (SIP) call handling of Cisco IP Phone 8800 Series devices could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition due to the SIP process unexpectedly restarting. All active phone calls are dropped as the SIP process restarts. More Information: CSCvc29353. Known Affected Releases: 11.0(0.1). Known Fixed Releases: 11.0(0)MP2.153 11.0(0)MP2.62.
A vulnerability in the update process for the dynamic JAR file of the Cisco Context Service software development kit (SDK) could allow an unauthenticated, remote attacker to execute arbitrary code on the affected device with the privileges of the web server. More Information: CSCvb66730. Known Affected Releases: 2.0.
A vulnerability in the email message scanning of Cisco AsyncOS Software for Cisco Email Security Appliance (ESA) could allow an unauthenticated, remote attacker to bypass configured filters on the device, as demonstrated by the Attachment Filter. More Information: CSCvd34632. Known Affected Releases: 10.0.1-087 9.7.1-066. Known Fixed Releases: 10.0.2-020 9.8.1-015.
A vulnerability in the feature-license management functionality of Cisco Firepower System Software could allow an unauthenticated, remote attacker to bypass URL filters that have been configured for an affected device. More Information: CSCvb16413. Known Affected Releases: 6.0.1 6.1.0 6.2.0 6.2.1. Known Fixed Releases: 6.2.1 6.2.0.1 6.1.0.2.
A vulnerability in the AutoVNF logging function of Cisco Ultra Services Framework could allow an unauthenticated, remote attacker to create arbitrary directories on the affected system. More Information: CSCvc76652. Known Affected Releases: 21.0.0.
A vulnerability in how DLL files are loaded with Cisco AnyConnect Secure Mobility Client for Windows could allow an authenticated, local attacker to install and run an executable file with privileges equivalent to the Microsoft Windows SYSTEM account. The vulnerability is due to incomplete input validation of path and file names of a DLL file before it is loaded. An attacker could exploit this vulnerability by creating a malicious DLL file and installing it in a specific system directory. A successful exploit could allow the attacker to execute commands on the underlying Microsoft Windows host with privileges equivalent to the SYSTEM account. The attacker would need valid user credentials to exploit this vulnerability. This vulnerability affects all Cisco AnyConnect Secure Mobility Client for Windows software versions prior to 4.4.02034. Cisco Bug IDs: CSCvc97928.
A vulnerability in the web interface of Cisco Prime Collaboration Provisioning Software (prior to Release 11.1) could allow an authenticated, remote attacker to delete any file from an affected system. The vulnerability exists because the affected software does not perform proper input validation of HTTP requests and fails to apply role-based access controls (RBACs) to requested HTTP URLs. An attacker could exploit this vulnerability by sending a crafted HTTP request that uses directory traversal techniques to submit a path to a desired file location on an affected system. A successful exploit could allow the attacker to delete any file from the system. Cisco Bug IDs: CSCvc99618.
A vulnerability in the ICMP ingress packet processing of Cisco TelePresence Collaboration Endpoint (CE) Software could allow an unauthenticated, remote attacker to cause the TelePresence endpoint to reload unexpectedly, resulting in a denial of service (DoS) condition. The vulnerability is due to incomplete input validation for the size of a received ICMP packet. An attacker could exploit this vulnerability by sending a crafted ICMP packet to the local IP address of the targeted endpoint. A successful exploit could allow the attacker to cause a DoS of the TelePresence endpoint, during which time calls could be dropped. This vulnerability would affect either IPv4 or IPv6 ICMP traffic. This vulnerability affects the following Cisco TelePresence products when running software release CE8.1.1, CE8.2.0, CE8.2.1, CE8.2.2, CE 8.3.0, or CE8.3.1: Spark Room OS, TelePresence DX Series, TelePresence MX Series, TelePresence SX Quick Set Series, TelePresence SX Series. Cisco Bug IDs: CSCvb95396.
A vulnerability in the Internet Key Exchange Version 1 (IKEv1) XAUTH code of Cisco ASA Software could allow an authenticated, remote attacker to cause a reload of an affected system. The vulnerability is due to insufficient validation of the IKEv1 XAUTH parameters passed during an IKEv1 negotiation. An attacker could exploit this vulnerability by sending crafted parameters. Note: Only traffic directed to the affected system can be used to exploit this vulnerability. This vulnerability only affects systems configured in routed firewall mode and in single or multiple context mode. This vulnerability can be triggered by IPv4 or IPv6 traffic. A valid IKEv1 Phase 1 needs to be established to exploit this vulnerability, which means that an attacker would need to have knowledge of a pre-shared key or have a valid certificate for phase 1 authentication. This vulnerability affects Cisco ASA Software running on the following products: Cisco ASA 1000V Cloud Firewall, Cisco ASA 5500 Series Adaptive Security Appliances, Cisco ASA 5500-X Series Next-Generation Firewalls, Cisco ASA Services Module for Cisco Catalyst 6500 Series Switches and Cisco 7600 Series Routers, Cisco Adaptive Security Virtual Appliance (ASAv), Cisco ASA for Firepower 9300 Series, Cisco ISA 3000 Industrial Security Appliance. Fixed versions: 9.1(7.7) 9.2(4.11) 9.4(4) 9.5(3) 9.6(1.5). Cisco Bug IDs: CSCuz11685.
A vulnerability in the DNS input packet processor for Cisco Prime Network Registrar could allow an unauthenticated, remote attacker to cause the DNS process to momentarily restart, which could lead to a partial denial of service (DoS) condition on the affected system. The vulnerability is due to incomplete DNS packet header validation when the packet is received by the application. An attacker could exploit this vulnerability by sending a malformed DNS packet to the application. An exploit could allow the attacker to cause the DNS process to restart, which could lead to a DoS condition. This vulnerability affects Cisco Prime Network Registrar on all software versions prior to 8.3.5. Cisco Bug IDs: CSCvb55412.
A vulnerability in the web-based GUI of Cisco Integrated Management Controller (IMC) 3.0(1c) could allow an authenticated, remote attacker to execute arbitrary code on an affected system. The vulnerability exists because the affected software does not sufficiently sanitize specific values that are received as part of a user-supplied HTTP request. An attacker could exploit this vulnerability by sending a crafted HTTP request to the affected software. A successful exploit could allow the attacker to execute arbitrary code with the privileges of the user on the affected system. Cisco Bug IDs: CSCvd14578.
A vulnerability in the web-based GUI of Cisco Integrated Management Controller (IMC) 3.0(1c) could allow an authenticated, remote attacker to execute arbitrary commands on an affected system. The vulnerability exists because the affected software does not sufficiently sanitize user-supplied HTTP input. An attacker could exploit this vulnerability by sending an HTTP POST request that contains crafted, deserialized user data to the affected software. A successful exploit could allow the attacker to execute arbitrary commands with root-level privileges on the affected system, which the attacker could use to conduct further attacks. Cisco Bug IDs: CSCvd14591.